HOW TO DO AN ADVANCED SEARCH.
Mon Jul 08, 2013 3:56 pm by Admin
For the benefit of 944Hybrids users there are two search functions available for you to use.
The purpose of this sticky is to explain the "Advanced Search" function because it is much more powerful and is the best choice when researching information.
When you log on to the site a list of options is shown in a line at the top of the page. One option is labelled "Search", use this option (NOT the search box lower down on the right).
After you click on the upper search option, a drop down box appears. At the bottom of this box is a radio button marked "Advanced …
Comments: 0
Similar topics
Latest topics
Log in
WTB: TT bearing carrier
4 posters
944Hybrids: 924/944/968 and 928 V8 Conversions :: For Sale & Wanted :: For Sale & Wanted (Vendors Limited...)
Page 1 of 1
WTB: TT bearing carrier
Hi all,
I'm in need of a good TT bearing carrier, the part that goes on the the outside of the bearing between the TT and the bearing.
If you have a good sleeve, that goes between the shaft and the bearing, I'll take that too.
Thanks!
Andy
I'm in need of a good TT bearing carrier, the part that goes on the the outside of the bearing between the TT and the bearing.
If you have a good sleeve, that goes between the shaft and the bearing, I'll take that too.
Thanks!
Andy
acorad- Posts : 697
Join date : 2010-12-21
Location : Agoura Hills, CA
Re: WTB: TT bearing carrier
Thanks Mike, great idea.
acorad- Posts : 697
Join date : 2010-12-21
Location : Agoura Hills, CA
Re: WTB: TT bearing carrier
If you can't find one make one, or all 4 like I did, from Delrin.
[You must be registered and logged in to see this link.]
[You must be registered and logged in to see this link.]
948- Moderator
- Posts : 573
Join date : 2009-06-09
Age : 109
Location : East PA
Re: WTB: TT bearing carrier
I think Clarks only has the plans for the inner sleeve between the drive shaft and the bearing, are there plans for the outer carriers? That donut between the TT tube and the outside of the bearing?
acorad- Posts : 697
Join date : 2010-12-21
Location : Agoura Hills, CA
Re: WTB: TT bearing carrier
I thibk Xschop was making bearinbg carriers in his TT thread.
87-944S- Posts : 744
Join date : 2009-06-10
Location : Maryland
Re: WTB: TT bearing carrier
Sorry, I must have skimmed your post and only read the last part....acorad wrote:I think Clarks only has the plans for the inner sleeve between the drive shaft and the bearing, are there plans for the outer carriers? That donut between the TT tube and the outside of the bearing?
Ask Rob about replacement bearing holders.....
948- Moderator
- Posts : 573
Join date : 2009-06-09
Age : 109
Location : East PA
Similar topics
» So....I think i need a throwout bearing
» I need some help with the pilot bearing
» Slave Cylinder Spacing from Clutch Fingers
» I need some help with the pilot bearing
» Slave Cylinder Spacing from Clutch Fingers
944Hybrids: 924/944/968 and 928 V8 Conversions :: For Sale & Wanted :: For Sale & Wanted (Vendors Limited...)
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum
Today at 3:06 pm by Rob44
» LEAKING TPC HYDROBOOST
Wed May 01, 2024 8:32 am by Rob44
» Fesler Saratoga Top
Tue Apr 30, 2024 8:28 am by JW1970
» Parts availability for general maintenance?
Mon Apr 29, 2024 10:36 pm by zenon
» What coilover spring rates are you running with torsion bar removed?
Mon Apr 29, 2024 10:24 pm by zenon
» 944 Turbo TPC Radiator Install Help Needed
Sun Apr 28, 2024 9:38 am by SpeedRacer11
» HYDRAULIC THROWOUT/RELEASE BEARING NOT ENGAGING FULLY
Sun Apr 28, 2024 12:00 am by Raymond-P
» Best engine uprights/plates
Sat Apr 27, 2024 11:09 pm by Raymond-P
» Rear coilover suspension setup
Fri Apr 26, 2024 3:30 pm by ThomasJoseph315
» Ray's 1987 944 LS1 Build & Swap
Mon Apr 15, 2024 6:59 pm by JW1970