HOW TO DO AN ADVANCED SEARCH.

Mon Jul 08, 2013 3:56 pm by Admin


For the benefit of 944Hybrids users there are two search functions available for you to use.
The purpose of this sticky is to explain the "Advanced Search" function because it is much more powerful and is the best choice when researching information.

When you log on to the site a list of options is shown in a line at the top of the page. One option is labelled "Search", use this option (NOT the search box lower down on the right).

After you click on the upper search option, a drop down box appears. At the bottom of this box is a radio button marked "Advanced …

Comments: 0

Latest topics
» LS3 conversion
Today at 12:30 pm by sharkey

» 944 with LS3 Brake Fluid Fire Mistake
Today at 8:54 am by Rich L.

» Boxster Rear Calipers
Yesterday at 5:04 pm by AMFCSL

» Transaxle rebuild
Fri Jul 20, 2018 9:24 pm by sharkey

» Noisy VSS and stalling???
Fri Jul 20, 2018 8:27 pm by matt889

» Hello, Gentlemen.
Fri Jul 20, 2018 7:43 pm by rawr

» alignment specs
Fri Jul 20, 2018 12:53 am by sharkey

» A/C parts used for the swap !
Thu Jul 19, 2018 8:04 pm by Rothaus

» Drive shaft too short to reach pilot bearning
Wed Jul 18, 2018 10:28 pm by spence

» 944 with LS3 bucking or jerking while cruising or low speed problem
Tue Jul 17, 2018 12:44 am by Porsche951toLS3

July 2018
MonTueWedThuFriSatSun
      1
2345678
9101112131415
16171819202122
23242526272829
3031     

Calendar Calendar

Log in

I forgot my password


Conversion almost complete.

Go down

Conversion almost complete.

Post  jonb944 on Sun Oct 06, 2013 10:22 pm

After two weeks of work I am nearly finished doing the conversion. I am waiting on the headers I ordered from Sanderson to complete the build. I would like to say that thanks to 944hybrids and the information that everyone has posted, the build went very well.  [You must be registered and logged in to see this image.] I had an adapter plate made for my bellhousing and set it up for hydraulic slave with remote bleeder (not shown).[You must be registered and logged in to see this image.][You must be registered and logged in to see this image.]I used low mount brackets to make room since the corvette accessories are on the right side of the motor which causes some issues.[You must be registered and logged in to see this image.]
I will posts more when I get finished.

jonb944

Posts : 8
Join date : 2013-08-01

Back to top Go down

Re: Conversion almost complete.

Post  RobotMachines on Mon Oct 07, 2013 10:35 am

Congratulations!

Might be a good time to think about making sure your water pump is in tip top shape. I just had to pull the radiator out to replace mine.
avatar
RobotMachines

Posts : 156
Join date : 2009-08-09
Location : Connecticut

Back to top Go down

Re: Conversion almost complete.

Post  Nomore4 on Mon Mar 07, 2016 5:51 am

RobotMachines wrote:Congratulations!  

Might be a good time to think about making sure your water pump is in tip top shape.  I just had to pull the radiator out to replace mine.  

"RobotMachines" where in CT are you? I am stuck with a LT conversion and am looking for a shop to complete my build. Drop me a note if you have any ideas of local "experts". 203-415-6151

Nomore4

Posts : 6
Join date : 2015-10-26

Back to top Go down

Re: Conversion almost complete.

Post  Sponsored content


Sponsored content


Back to top Go down

Back to top


 
Permissions in this forum:
You cannot reply to topics in this forum